Weekly pool cleaning & maintenance plans across the Oklahoma City metroCall (405) 972-8768
OKC Pool CleaningService · OKC Metro
Home/Services/Pool Equipment Repair
Pumps, filters, heaters, salt

Pool Equipment Repair in the Oklahoma City Metro

Pump won't prime? Filter pressure through the roof? Heater won't fire, or salt system flashing an error? We diagnose the actual problem first, then tell you plainly whether it's a repair or a replacement.

Get a Free Quote Call (405) 972-8768

Robotic pool cleaner and pool equipment working in a clear pool

What we repair

Residential pool equipment from the major manufacturers: pumps, filters, heaters, salt chlorine generators, automation and cleaners.

Pumps & motors

Loss of prime, air leaks at the lid or unions, noisy bearings, failed capacitors, leaking shaft seals and full motor or pump replacement, including single-speed to variable-speed upgrades.

Filters

Cartridge, sand and DE filters: high pressure, short cycles, torn grids or cartridges, cracked tanks, leaking multiport valves and full media changes.

Heaters & heat pumps

Ignition and flow faults, pressure switch errors, scale-related issues and pre-season checks so a heater works the first cool weekend you need it.

Salt systems

Cell cleaning and inspection, flow and salt sensor faults, low-output diagnosis and cell or control-board replacement.

Automation

Schedules, pump speed programs, valve actuators, lighting circuits and app connectivity for pools running control panels.

Plumbing & leaks

Leaking valves and unions at the pad, cracked fittings after a freeze, and the bucket-test and dye-test first steps before full leak detection.

Repair or replace: how we make the call

Every recommendation weighs three things: the age and condition of the equipment, what the repair actually costs compared with replacement, and how much a newer unit would save you in running costs. A 15-year-old single-speed pump with a burned-out motor almost always makes sense to replace with a variable-speed model. A three-year-old variable-speed pump with a leaking seal is a straightforward repair.

You get the numbers both ways, in writing, before any work starts.

Oklahoma weather is hard on pool equipment

Summer heat pushes equipment pads hot, and pumps that run all day at high speed wear out bearings and seals faster. Spring storms bring power surges and flooding. The big freezes do the most damage. In February 2021, Oklahoma City recorded −14°F, and pools across the metro with stopped pumps cracked valve bodies, pump housings and filter heads. Freeze-protection setup is part of our seasonal service.

Underwater view of a blue tiled swimming pool with circulating water

Typical repair ranges in the metro: pump motor repair $150–$400, variable-speed pump replacement $1,200–$2,200 installed, salt cell replacement $500–$1,200, heater repair $150–$600. Actual prices depend on the brand and the parts involved.

Equipment problems we see most across the metro

Many repair calls in the Oklahoma City area trace back to a few local causes, and some are not broken equipment at all.

  • High filter pressure in spring. Red-dirt wind and the May cottonwood drop load cartridges and sand beds quickly. Pressure climbs, flow drops, and a salt system may show a low-flow error even though the cell is fine. A thorough filter cleaning often fixes what looks like a failed part.
  • Scaled salt cells and heaters. OKC tap water and spring runoff push calcium hardness up over a season. Once it is high enough, scale builds on salt cell plates and inside a heater’s heat exchanger, cutting chlorine output and causing flow and overheating faults. Cleaning the cell and correcting the water comes before replacing anything.
  • Storm damage at the pad. Spring storms bring power surges that can take out a control board, an automation panel or a pump drive, and heavy runoff can flood a low equipment pad.
  • Freeze cracks. A pump that stops during a hard freeze is how valve bodies, pump housings and filter heads crack. The damage usually shows up as a leak at the pad when the system restarts.
  • Newer systems, newer faults. Homes in Moore and the newer subdivisions around Yukon often run a variable-speed pump, a salt system and automation together. Many of those calls turn out to be programming, sensor or communication faults rather than a worn-out part.

What to check before you call

A few quick checks can save a visit, or at least make the diagnosis faster:

  • Has the pump breaker or GFCI tripped? Reset it once. If it trips again, leave it off and call.
  • Is the water high enough that the skimmer isn’t pulling air, and are the skimmer and pump baskets empty?
  • What does the filter gauge read compared with its normal clean pressure?
  • Is the salt system, heater or automation panel showing an error code? A photo of it helps.

Send what you find with the request form. Repair ranges are on the pricing page, and pools on weekly pool cleaning get the pad checked every visit.

Pool equipment repair FAQ

Should I repair or replace my old pool pump?

If a single-speed pump needs a new motor, replacing it with a variable-speed pump often makes more sense. Federal efficiency rules have required most replacement pumps to be variable-speed since 2021, and the energy savings in a long Oklahoma swim season add up. If the pump is newer and the issue is a seal, capacitor or bearing, repair is usually the right call.

How long do salt cells last?

Many last three to five years, depending on run time, how well pH is controlled and how often they scale. A cell that needs frequent cleaning, or reads low salt when the salt is fine, is usually near the end.

Do you charge to diagnose a problem?

Yes, a diagnostic visit is charged, typically $65–$110 in the metro, and it's credited toward the repair if you go ahead with it. Weekly customers usually get equipment issues flagged during regular visits at no extra charge.

Why is my pool pump running but not moving water?

Usually it has lost prime. The common causes are low water at the skimmer, a full skimmer or pump basket, an air leak at the pump lid or a union, or a clogged impeller. Turn it off rather than let it run dry, since that can ruin the shaft seal. If clearing the baskets and topping off the water doesn't fix it, a diagnostic visit will find the leak or blockage.

What should I do with pool equipment during a hard freeze?

Keep the pump running. Water moving through the pipes, pump and filter is what keeps them from cracking, so use the freeze-protection setting or set the timer to run through cold nights. A power outage during a freeze is the main risk; if the power stays off, call before the equipment sits frozen.

Equipment repair service areas

Something not running right?

Describe what the equipment is doing, or not doing, and we'll schedule a diagnostic visit.

Tap to call · (405) 972-8768